Reconditioned Valeo starter motor and solenoid in black and silver finish. Professionally reconditioned and sold with a 12 month guarantee. This is a suitable replacement for Bosch 8 or 9 tooth Guzzi starter motors. Minor modification may be required on some pre 1990 models to make room for the solenoid. Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology. See , see this link for the modifications required to fit a Valeo starter to a 4 speed model.

This is an exchange only item, we can supply these before receiving your exchange unit subject to a refundable deposit so you can keep your bike on the road. See ELC10737 for the refundable deposit. Send your old starter motor to our registered address. NB In case of starter motor problems do not tap the casing as this will certainly cause it to fail. See SSA08075 for mounting bolts. Also known as Guzzi ref. 30730710
Do not remove second nut from terminal posts when fitting - this nut is required to hold the terminal in place

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Complete replica sump for 850, 1000 and some 1100 models. Out of production for years, this is a good opportunity to replace a chipped or cosmetically damaged sump on your Guzzi

 This part is available by special order, request a quote

 14003500 GU14003500 14 00 35 00
 1400 3500 1400.3500 14.00.35.00

Splined drive plate incorporating cush drive (rubbers not included)

See WHA14336 for cush drive rubbers

 This part is available by special order, request a quote

 14335203 GU14335203 14 33 52 03
 1433 5203 1433.5203 14.33.52.03

Pair of chrome reverse cone mega type silencers supplied with shims to allow fitment to a variety of models. Adjustable mounting bracket and clamp included.

You may need to modify brackets or fabricate your own depending upon which model you have

 This part is available by special order, request a quote

Replacement clutch plate for single plate RAM clutches

Torque setting for fitting this is 25Nm with a thread locking compound

 This part is available by special order, request a quote

Rear main bearing flange

 This part is available by special order, request a quote

12011400-z 12011400 GU12011400 12 01 14 00
 1201 1400 1201.1400 12.01.14.00

Complete twin bleed F09 (P9) front left hand (when mounted behind fork leg, otherwise use as RH) replica Brembo brake caliper. Also rear caliper (when mounted above and behind rear wheel spindle). Supplied with bleed nipples, dust cover, pins and spring. This can replace the P9 rear caliper as fitted to a 1000 SP, or can be used as a performance upgrade to replace the smaller piston P8 caliper fitted as standard to many Guzzis. Please see Guzziology for advice on how to perform this conversion.

Brake pads not included- see BRA33204

 This part is available by special order, request a quote

Complete twin bleed F09 (P9) front right hand (when mounted behind fork leg, otherwise use as LH) replica Brembo brake caliper. Supplied with bleed nipples, dust cover, pins and spring. This can be used as a performance upgrade to replace the smaller piston P8 caliper fitted as standard to many Guzzis. Please see Guzziology for advice on how to perform this conversion.

Brake pads not included- see BRA33204

 This part is available by special order, request a quote

Rear main bearing flange, second oversize: + 0.4mm

 This part is available by special order, request a quote

12011402-z 12011402 GU12011402 12 01 14 02
 1201 1402 1201.1402 12.01.14.02

Rear main bearing flange, third oversize: + 0.6mm

 This part is available by special order, request a quote

12011403-z 12011403 GU12011403 12 01 14 03
 1201 1403 1201.1403 12.01.14.03